This forum has been archived. You will not be able to log in, register, or post.

Main >> General Forum Thread views: 151788

Pages in this thread: 1 2 3 4 (5)  
ChullSS
Posts: 66
Re: New guy   Posted Fri Jul 27, 07   12:59 PM     

that's a good friend. Why the whole beaner thing?
We found out why the gears were hard to slam, he bent one of the shaft from the shift linkage. Fixing that as we speak and he is also mounting some Hannkook slicks. All this to beat an auto ls1

Rx_otary_Se7en

Posts: 1646
Re: New guy   Posted Sun Jul 29, 07   12:11 AM     

What tranny is he using?


"go wack you balls to a picture of 2 faggets you homo" << Direct quote from FastFiveO

[External Image Removed]
ChullSS
Posts: 66
Re: New guy   Posted Sun Jul 29, 07   2:54 PM     

It's a B16 cable transmission

Rx_otary_Se7en

Posts: 1646
Re: New guy   Posted Sun Jul 29, 07   11:07 PM     

He must not be very built up then if you're beating his ass that bad.


"go wack you balls to a picture of 2 faggets you homo" << Direct quote from FastFiveO

[External Image Removed]
ChullSS
Posts: 66
Re: New guy   Posted Mon Jul 30, 07   11:57 AM     

Nope it's a stock ls/v-tec .
B20 with a second gen B16 head, cold air, headers and straight pipe. Car's race weight is 2450 with driver and striped out interior.
I'm thinking around 165-170hp and about 155tq
My friends GSR is about the same. I will post the vid from that race.

Rx_otary_Se7en

Posts: 1646
Re: New guy   Posted Mon Jul 30, 07   9:01 PM     

Those are whp estimates or flywheel estimates?


"go wack you balls to a picture of 2 faggets you homo" << Direct quote from FastFiveO

[External Image Removed]
ChullSS
Posts: 66
Re: New guy   Posted Sat Aug 4, 07   1:30 PM     

I was thinking Engine hp.
Did some looking around and i would say more like 165-170 tq

Rx_otary_Se7en

Posts: 1646
Re: New guy   Posted Sun Aug 5, 07   1:55 AM     

What pistons is he using? The stock B20 pistons or something else. Was it a B20B or B20Z? Just looking for compression numbers. It should be more around 180hp.


"go wack you balls to a picture of 2 faggets you homo" << Direct quote from FastFiveO

[External Image Removed]
ChullSS
Posts: 66
Re: New guy   Posted Sun Aug 5, 07   7:58 PM     

Its a B20B. It did not seem like he has so much. then again who knows how good he did his conversion.

Rx_otary_Se7en

Posts: 1646
Re: New guy   Posted Wed Aug 8, 07   7:28 PM     

He has stupid low compression. Tell him to stop being cheap and swap out those pistons.


"go wack you balls to a picture of 2 faggets you homo" << Direct quote from FastFiveO

[External Image Removed]
ChullSS
Posts: 66
Re: New guy   Posted Wed Aug 8, 07   9:28 PM     

He said their good for Nitrous. Is that true?

lloyd
Posts: 15
Re: New guy   Posted Thu Jan 10, 08   10:28 AM     

i got d nissan skyline

NOS
Posts: 329
Re: New guy   Posted Fri Jan 11, 08   8:31 PM     

your a faggot


if u read this than FUCK YOU

go fuck yourself motherfucker
Rx_otary_Se7en

Posts: 1646
Re: New guy   Posted Sat Jan 19, 08   1:18 PM     

Good for nitrous and forced induction in general. However theres no point in having a vtec head if he is going to run low compression like that. He could run nitrous with 9.6ish compression just fine if he BUILT it right.


"go wack you balls to a picture of 2 faggets you homo" << Direct quote from FastFiveO

[External Image Removed]
SweetNeon

Posts: 2404
Re: New guy   Posted Sun Mar 2, 08   8:54 AM     

That car is way to heavy. With alittle more cuting you can have a light weight honda like me.

[External Image Removed]

[External Image Removed]

Pages in this thread: 1 2 3 4 (5)